Add reverb to audio

Add reverb to place a dry recording in a room, a hall or a cathedral. Set how much reverb to blend in and how long the space rings, and hear the result as it plays.

Loading the tool…

How to add reverb to audio

  1. Drop a vocal, an instrument or any recording here, or press Use a demo loop.
  2. Press Preview to hear the starting setting: 45% reverb in a three-second room.
  3. Choose Room size: 1 second for a tight room, 2 to 3 seconds for a hall, 4 to 6 seconds for a cathedral.
  4. Set Reverb to balance the original against the space. Lower values keep the sound close; higher values push it into the distance.
  5. Press Download WAV. Three seconds after the end of the audio are kept so the tail can fade.

Room size, explained

Room size sets how long the reverb takes to fade to silence, from 1 to 6 seconds. Real spaces cover a similar range: small rooms die away in well under a second, concert halls ring for around two seconds, and large stone churches can ring for five seconds or more.

Room sizeSounds likeGood for
1 secondA large room or small clubAdding life to a dry voice or instrument without obvious reverb
2 secondsA concert hallSinging, piano, acoustic guitar and strings
3 secondsA big hall or a churchSlow ballads, choirs and lush pads
4 to 6 secondsA cathedral or a cavernAmbient music, sound design and dramatic effects

How much reverb to use

  • Speech: 5 to 15%, small room. Just enough to take the edge off a closet-dry recording.
  • Vocals in a song: 20 to 35%. Enough to sit the voice in a space while every word stays clear.
  • Acoustic instruments: 20 to 40%. Piano and guitar recorded at home often sound boxed in without it.
  • Ambient and pads: 50 to 80%, long rooms. Here the reverb is part of the sound.
  • Effects: 80 to 100%. The sound turns distant and ghostly.

Fast music needs less reverb than slow music, because long tails smear quick notes together. If a mix gets cloudy, shorten the room before you lower the amount.

How this reverb is made

The reverb is a convolution reverb with a generated impulse response: a dense burst of sound that fades smoothly over the room length you choose, slightly different in each ear, which gives a wide stereo tail. It has no distinct early echoes and no pre-delay, so it sounds like a smooth, idealized space rather than one particular building. The Reverb slider blends that tail with your original, and even at 100% some of the original sound stays in the mix, so it never disappears completely.

Reverb also shapes how big a voice or instrument feels. For the slowed, dreamy sound heard in slowed and reverb edits, use the slowed and reverb generator, which pairs reverb with a slower speed. To make the reverb itself less boomy or bright, adjust the result in the audio equalizer.

Questions

Can this tool remove reverb from a recording?

No. Taking reverb out of a recording is a much harder problem that needs specialized de-reverb software. This tool only adds it, so keep your original dry file in case you want to try a different setting later.

What is the difference between reverb and echo?

Echo is a distinct repeat you can hear separately, like a shout bouncing off a far wall. Reverb is thousands of reflections arriving so close together that they blend into one smooth tail. For a clear echo on a voice, try the Echo setting in the voice changer.

Why does the end of my file sound cut off?

The download keeps three seconds after the audio ends. Rooms longer than that are still ringing when the file stops. If your recording ends abruptly, choose a room size of three seconds or less, or record a few seconds of silence at the end.

Should I add reverb to a podcast or voice note?

Usually only a touch, 5 to 15% with a small room. Speech with a lot of reverb is harder to understand, especially on phone speakers and for listeners who are hard of hearing.

Does the reverb run on a server?

No. The convolution is calculated by your own browser, which is why a long file takes a few seconds on an older phone. Nothing is uploaded.